Two-zone Thermal Shock Test Chamber
Specification
Temperature Specification
Temperature Specification
High temperature chamber: （1）Max preheating temperature: +200℃
（2）Heating time：RT→+200℃≤25min
Remark：The heating time is the performance of the high temperature chamber when it is running alone.
Low temperature chamber：（1）Min precooling temperature：-55℃
（2）Cooling time：RT→-55℃≤60min
Remark：The cooling time is the performance of the low temperature chamber when it is running alone.
Test Zone：（1）High temperature shock range：+60℃~+180℃
（2）Low temperature shock range：-40℃~0℃
Temperature fluctuation：≤±0.5℃
Temperature uniformity：≤±2.0℃
Temperature deviation：±2.0℃（≤+150℃），±3.0℃（＞+150℃）
Shock recovery time：within ≤5min
Temperature conversion time：within 3s
Internal volume：80L-150L-225L-408L-800L-1000L-1500L（Customizable）
Two-zone Thermal Shock Test Chamber Briefly introduction
High and low temperature (two cases) thermal shock test chamber system structure can be divided into two parts. Namely, high temperature tank (preheating zone), cryogenic tank (pre-cooling zone).
Two-zone Thermal Shock Test Chamber Testing principle
Two Zone Thermal Shock Test Chamber Testing principle mainly through controlling the portable basket (test samples District) to quickly move between cryogenic tank and high temperature tank to achieve rapid thermal shock test. The whole testing process test samples along with mobile gondola to move together. The test chaber is suitable for the examination of the whole set of products, components, parts and materials subjected to rapid changes in temperature. The temperature impact test chamber are used in a shortest time to evaluate the test samples due to thermal expansion and contraction caused by the changes of chemical or physical damage.
The advantages of TALENTS Two-zone Thermal Shock Test Chamber
1.Thermal Shock Test Chamber Temperature and humidity setting protection
2.Two zone thermal shock test chamber. Air pressure driven test area(sample)
3.Error failure medical record table cartilage device
4.HFC environmentally friendly refrigerant, SWEP plate heat exchanger, two type refrigeration system
5.Optimal structure and high efficiency refrigeration machinery design
6.Air intakes and returns with sensor control
7.Sever Valve, Kinetic energy automatic load control
8.Testing range: 150(60)℃~ (-10)-65℃
9.50% power saving efficiency and automatic servo control
10.Compatible with BUS CM remote monitoring management system
11.Can expanded: LN2V liquid nitrogen rapid cooling control device
12.Thermal shock test chamber movement time is 10 seconds.Can meet MIL, IEC and JIS standard.
13.Wind valve switching time is 10 seconds
14. Thermal shock test chamber temperature recovery time is 5 minutes, can meet the test specification
15.The end of the experiment, the product automatically return to the normal temperature to avoid frost dew
16.The world's first built-in USB2.0 interface digital recorder (recording can be plugged in at any time)
17.Industrial grade upright full-color touch multilingual programmable control system
18.The world's first standard shipping included USB2.0 and disk storage machine dual interface
19.The protective mechanism of return to normal temperature after the test is finished.
20.The world's first complete test curve analysis shows that there is no time limit.
Our services
Pre-Sales
1.Technical consultation: test method, laboratory planning and suggestion.
2.Equipment selection: selection scheme, FAQ.
3.Product testing scheme.
In-Sales
- 1.Customer communication and progress report.
- 2.Guidance for pre-installation preparation,equipment commissioning and test run.
- 3.Calibration (when Third Party's verification is required)
After-Sales
- 1.Technical training: operation of equipment, daily maintenance,common fault diagnosis and troubleshooting.
- 2.Scheduled on-site service: Detection of problem as soon as possiblein order to eliminate equipment and anthropogenic hazards. This is toensure long term and stable equipment operation as well as delivery oflatest technical information.
- 3.Technical support: special paid services are provided according tocustomer's needs.
Q1：How to get testing solution and quotation?
A1：If your product requires environmental testing, please contact us to get testing solution and quotation. We will respond to your request within
12 hours.
Q2：How to contact us?
A2：1.Phone: +886 976 590 796
2. E-mail: sales@zh-talents.com
Q3：How to place an order?
A3：If all the details of the products are confirmed,we can draft a contact to you.Also you can send the PO to us by mail.
Q4：How to deal with equipment problems and how to guarantee after-sales service?
A4：If there is problem with the equipment, please contact us and we will reply within 12 hours and arrive at your site within 48 hours.
We have after-sales service offices in Southeast Asia, Taiwan, Hong Kong and other places, and cooperative service providers in other regions.
Q5：How is the product packaged and shipped through logistics?
A5：1. Use export standard wooden boxes for packaging.
2. Choose the most favorable transportation method. Sea freight, air freight, railway, truck transportation, and multimodal transportation.
3. Fast delivery, some models are in stock and will be shipped in 1-3 days.
